Concrete Guard ProCommercial Concrete Sealer & Protective Coating
- Penetrating Concrete Protection - quarter-inch molecular bond outperforms surface coatings
- Industrial Floor Coating - resists oil, fuel, hydraulic fluids and chemical spills
- Chloride and Salt Barrier - defends against de-icing salts, freeze-thaw and moisture intrusion
- Fire-Tested Surface - Heat Index 0 on ASTM E162 surface flammability test
- 5-Year Limited Warranty (covers product defects) · 1,200+ PSI adhesion, lab-tested
Overview
Concrete Guard Pro is a commercial concrete sealer and protective coating that forms a non-permeable barrier against oil, fuel, hydraulic fluids, chemical spills and de-icing salts. It carries a 5-Year Limited Warranty covering product defects and lab-tested 1,200+ PSI adhesion (ASTM D4541).
Oil, fuel, and hydraulic fluid spills soak into unprotected concrete, leaving permanent stains and gradually breaking down the surface - and the repair bill grows the longer the slab stays unsealed.
Concrete Guard Pro stops this damage cycle with a nano-polymeric coating that forms a non-permeable barrier resistant to peeling and flaking. It dries to a clear gloss finish and can also be applied as a top coat.
Lab-Tested Performance Data
- Adhesion Strength: +1,200 PSI (polished concrete substrate)
- Solvent Resistance: 1,000 MEK double rubs, no effect (ASTM D4752)
- UV Stability: <0.5 dE color shift after 1,000 hours (ASTM G154)
- Shore D Hardness: 72 (ASTM D2240)
- Abrasion Resistance: 23 mg loss, CS-17 wheel, 1,000 cycles (ASTM D4060)
Environmental and Compliance Standards
- Temperature Range: -200°F to +350°F (cryogenic to high-heat processing)
- Chemical Resistance: oil, fuel, jet fuel, hydraulic fluids, caustic wash solutions, bird and animal waste
- Protection Class: water intrusion, chloride penetration, deicing salt damage, salt spray (coastal applications)
Recommended Applications
Parking Structures and Garages: Parking decks, ramps, and garage floors.
Industrial and Commercial Floors: Concrete floors in industrial facilities and commercial buildings.
Exterior Concrete and Masonry: Exterior walls and structures, masonry pavers, bricks, and cement blocks.
Decks, Balconies, and Spill Containment: Concrete decking, balconies, and spill containment areas.
Residential Concrete: Residential concrete floors and exterior surfaces.
Product specs
- Coverage: 200-600 sq ft/gallon (varies by surface porosity and texture)
- Application: HVLP or airless sprayer, or roller. Check surface compatibility before application.
- VOC Content: <100 g/L (solvent-based)
- Finish Options: clear gloss
- Cure Time: touch dry 2-3 hrs | Walk-on 8-12 hrs (light foot traffic) | Full cure 7 days | No rain 48 hrs
- Container Size: 5-gallon
- Shipping: ships in 3-5 business days. Expedited shipping not available.
- Safety: solvent-based, flammable (DOT Class 3). Use respirator and gloves - see SDS.
Frequently asked questions
Unlike thick, film-forming epoxies that can look “plastic,” Concrete Guard Pro penetrates the substrate to form a covalent bond while maintaining the natural texture of the concrete. It is a single-component system that is UV stable - preventing the yellowing common with epoxies.
Yes, it is a high-gloss clear coating.
Yes, the product is UV stable and performs well both indoors and outdoors. Accelerated UV testing (ASTM G154, 1000 hours) shows minimal change (dE < 0.5).
If applied properly at the recommended thickness, it generally maintains the natural texture of the surface, avoiding the slipperiness associated with thick epoxies.
Durability depends on usage and exposure (coastal/inland, chemicals, salt, abrasion). It comes with a 5-year warranty under recommended applications, but will perform longer under many conditions.
Yes. It helps revive color and provides an easy-to-clean gloss finish. Ensure old sealers are removed first for proper adhesion.
Absolutely. It is resistant to mild acids and to petrochemicals - gasoline, diesel, motor oil, hydraulic fluid. Spills are best cleaned up promptly.
Yes, it is non-permeable to water, saltwater, and other fluids.
Yes. Permanent marker can be wiped off with soap and water; spray paint may require a commercial removal solution.
Apply to a clean, dry surface. Use a commercial-grade HVLP (1.0-1.3 tip) airless sprayer (.111, .211, .311 tip). It can also be applied with a high-density ultra-smooth roller. Surface must be profiled to 600-grit (grinding or sandblasting), pH 7-9, moisture ≤13%. Remove old sealers, silicones and curing agents - if water beads on the surface, a sealer is still present. Apply one coat; a second coat only if the first is flawed.